honeywell thermostat not working blank screen

If you have a wire in the R terminal and no wire in the RC terminal verify the. If you have a wire in the C terminal you should have AC power and your Lyrics screen should not go blank.

4 Ways To Fix Honeywell Thermostat Backlight Not Working Diy Smart Home Hub

The other end goes into the socket where the thermostat should be plugged in.

. If your thermostat screen goes blank after several minutes of operation it could be due to the high-limit switch tripping. To fix this issue press and hold the Connect button on the wireless sensor for about 15 minutes. Loose Connections Could Be Why Your Honeywell Thermostat Screen Is Blank.

Check if yours has one because thermostats could be sensitive to that and even stop working if there is a problem. There could be an issue with your power supply or one of the thermostats safety features has been tripped. Httpsamznto2VJ2KFcHow to Make 4 Clip Jumper Wire.

So first make sure that the batteries are working and if not. Make sure it clicks to ensure it is properly seated. Please note my hours are 630pm to 5am MST mountain standard time if you reach me within that time frame I should be able to immediately respond however at times it may take a little while for a response depending on work load outside of.

Turn on Your HVAC Systems Circuit Breaker. Loose wires in the wiring of your HVAC system could be the reason for your Honeywell thermostat blank screen. If your Honeywell thermostat is not working and there is no display we recommend you work through the following troubleshooting steps.

To tell if your Lyric has AC power gently pull the thermostat away from the wallplate and look at your wiring. When your Honeywell thermostat display goes blank it is likely one of two problems. So here are some troubleshooting steps to try if your Honeywell thermostat screen has gone blank.

Tried all 4 in the brand. The TH9421C1004 is attached to a control unit. Verify the C wire is connected to the C terminal in your furnace or air handler.

What to do when your air conditioner is not working and the thermostat is blank. I thought it must be the battery so I replaced it. Overheating typically occurs due to poor airflow or parts that are going bad or broken.

Once you plug it in the screen should turn back on. Most furnaces have a high-limit switch that prevents the system from overheating. Either the battery is dead or the battery has some issues.

I thought it may have been the battery. To fix the display first make sure to pull the cable slightly up and back. Confirm you have a C wire in the C terminal.

Next return to your thermostat menu and press Menu Devices and then Sensors. Hi My name is Mike. If not continue to the next step.

To do so set the fan switch to auto and the switch at the top of your thermostat to COOL. After a brief power outage the Honeywell TH9421C1004 thermostat is a blank screen. Gently pull the thermostat away from the wallplate remove the battery and replace it with a new one.

Wait for the LED to turn Amber. In order for your Honeywell thermostat to work properly the doors should be closed and the sensors should be turned on. The easy diagnosis of this blank screen issue is that the batteries have died.

However it can also be caused by a thermostat thats on its last legs. Turn the dial to the lowest setting like 60 and wait for 5 minutes. Be careful not to strip the screws.

Thermostatic Controls - Honeywell TH9421C1004 Blank Screen - Its 9 degrees outside and my heat pump is not working. Check if the thermostat panel is pressed in. Im sorry you are having this issue I have accepted your question and will be happy to help you.

If you see your Honeywell thermostat screen blank after changing batteries the batteries can be the reason. If the air conditioner unit kicks in the COOL feature is functioning right. An unresponsive Honeywell thermostat screen is most commonly caused by a loose wire on the back a battery thats on its last legs or a tripped breaker.

Follow the instructions on the screen to. Replace the Batteries in Your Thermostat. Replace the battery with the new ones and then switch it on once again to check if there is a blank screen still or not.

Seeing your thermostat suddenly fail to do anything can be a bit of a nightmare. An HVAC system is made up of several complex wires and for the system to work properly each of these wires has to be properly and firmly connected. Check to see that everything is working.

I have forced air. Three wires going into the thermostat. If the display of your thermostat is not on or is fading your device might be losing power or not getting power at all.

The screen on my Honeywell RTH8500 Wi-Fi Series hads gone blank. Your thermostat display should work fine now. If your previous thermostat did not use a C wire its unlikely that it is connected at the equipment.

A blank display could also mean your thermostat is. If the batteries are dead they wont power the device. If there are no batteries providing power the Honeywell thermostat will not work or even display anything on the screen.

Honeywell Thermostat Blank Screen. The Honeywell thermostat will not work or even display anything on the screen. The first step will be to see if your thermostat is powered properly.

Short Pro Tool link. Check your jumper selector switch. You need to first identify whether the COOL feature is working or not.

Honeywell Thermostat Screen Not Responding Fixed Machinelounge